Gửi tin nhắn
Nhà Tin tức

tin tức công ty về Làm thế nào để điều chỉnh độ lệch máy tấm?

Chứng nhận
Trung Quốc Cangzhou Best Machinery Co., Ltd Chứng chỉ
Trung Quốc Cangzhou Best Machinery Co., Ltd Chứng chỉ
Khách hàng đánh giá
tôi hài lòng với Cangzhou BEST Machinery Co., Ltd. nhà máy rất chuyên nghiệp và đáng tin cậy. Họ cung cấp máy chất lượng tốt và dịch vụ bán hàng tốt, rất mong được hợp tác với họ một lần nữa.

—— Moyo

Máy móc của Cangzhou BEST Machinery co., ltd rất tốt, sản xuất nhanh, giao hàng nhanh. công ty rất hỗn loạn.

—— Octavio

Cảm ơn vì lòng hiếu khách của bạn. Công ty của bạn rất chuyên nghiệp, chúng ta sẽ có sự hợp tác tốt đẹp trong tương lai gần.

—— Cristian

công ty rất tốt. thông qua giao tiếp rất tốt, tất cả các vấn đề đã được giải quyết, tôi hài lòng với giao dịch mua hàng của mình.

—— Spence

very professional factory, realiable, happy with them

—— Samuel

dịch vụ bán hàng tốt, thời gian giao hàng nhanh. giao tiếp tốt.

—— Ali

Tôi trò chuyện trực tuyến bây giờ
Công ty Tin tức
Làm thế nào để điều chỉnh độ lệch máy tấm?
tin tức mới nhất của công ty về Làm thế nào để điều chỉnh độ lệch máy tấm?

(1) The level of the tile press machine is not adjusted properly, you can use a level ruler to straighten the channel steel at both ends of the machine, and the four legs of the machine are properly leveled with some iron plates.
(2) Find a large square ruler, measure the feed ruler behind the tile press, that is, the angle iron of the plate and the wheel of the tile press to find the right angle, this is very important, if the rear plate is not a right angle The color board must not go straight.
(3) Measure the diagonal of both ends of the machine to see if they are consistent, provided that the machine is adjusted horizontally. According to experience, the diagonal angle is less than 4 mm and can be adjusted. If it is greater than 4 mm, it is difficult to adjust. Even if it is adjusted, the walking plate is unstable.
(4) When encountering a machine that deviates, the principle is to look in the direction of entering the board, and in which direction the board runs, pad the feet of that machine. In fact, the diagonal is artificially adjusted to be consistent.
(5) Finally, measure whether your color steel equipment and the color steel coil you put are on a parallel line. Reminder: Deviation generally occurs after the color steel coil is replaced, and the coil and the machine are not in a straight line (the coil and the machine cannot be too close to maintain a distance of about 3 meters), resulting in the deviation of the board and the deviation of the tile

Pub Thời gian : 2020-04-22 11:48:55 >> danh mục tin tức
Chi tiết liên lạc
Cangzhou Best Machinery Co., Ltd

Người liên hệ: Mr. Arno Hao

Tel: +8618717894416

Gửi yêu cầu thông tin của bạn trực tiếp cho chúng tôi (0 / 3000)