(1) Glue compounding on the composite board: check whether the panel and bottom plate of the composite board production line are dry, and pick out the board with moisture. (1) Keo dán trên bảng tổng hợp: kiểm tra xem bảng và tấm dưới cùng của dây chuyền sản xuất bảng tổng hợp có khô không, và chọn bảng có độ ẩm. Adjust the glue, adjust the glue and calcium carbonate evenly, and adjust the toner to the same color as the panel. Điều chỉnh keo, điều chỉnh keo và canxi cacbonat đồng đều, và điều chỉnh mực có cùng màu với bảng điều khiển. According to the climate and humidity at the time, add an appropriate amount of curing agent, the ratio of curing agent to glue is 1 ~ 3%. Theo khí hậu và độ ẩm tại thời điểm đó, thêm một lượng chất đóng rắn thích hợp, tỷ lệ chất đóng rắn với keo là 1 ~ 3%.
(2) Pre-composite process of panel: if faced with a polished surface and a mesh panel, it must be carefully selected and sent to a hand-held grinder for de-glazing. (2) Quá trình tổng hợp trước của bảng điều khiển: nếu phải đối mặt với bề mặt được đánh bóng và bảng điều khiển bằng lưới, nó phải được lựa chọn cẩn thận và gửi đến máy mài cầm tay để khử kính. It is de-aired according to the flatness, dry-grinded and leveled, but not deep-grinded; Nó được khử khí theo độ phẳng, được mài khô và san phẳng, nhưng không được mài sâu; then the net is broken off Cloth shovel flat surface glue. sau đó lưới bị vỡ ra Xẻng vải phẳng bề mặt keo. If the shovel cannot be removed, you should use a hand-held grinder to grind off the net surface glue. Nếu xẻng không thể được gỡ bỏ, bạn nên sử dụng máy mài cầm tay để mài keo bề mặt lưới. Use double-sided smoothing to remove dust from the dry-milled panel. Sử dụng làm mịn hai mặt để loại bỏ bụi khỏi bảng điều khiển khô.
(3) The pre-composite process of the bottom plate: the bottom plate with light should be de-glazed and then thickened, usually the thickness of 20mm bottom plate should be 17mm. (3) Quá trình tiền tổng hợp của tấm đáy: tấm dưới cùng với ánh sáng nên được khử men và sau đó dày lên, thông thường độ dày của tấm đáy 20 mm nên là 17mm. After the bottom plate is fixed, remove moisture. Sau khi tấm dưới cùng được cố định, loại bỏ độ ẩm. Can be pulled outside to dry, dry or blow dry. Có thể kéo ra ngoài để khô, khô hoặc thổi khô. Note that if the board is not dry, it cannot be glued to avoid delamination or infirmity. Lưu ý rằng nếu bảng không khô, nó không thể được dán để tránh sự phân tách hoặc bệnh tật.
(4) Select panel: select the marble panel that meets the customer's requirements. (4) Chọn bảng điều khiển: chọn bảng điều khiển bằng đá cẩm thạch đáp ứng yêu cầu của khách hàng. Clarify the types of materials and the consistency of colors. Làm rõ các loại vật liệu và tính nhất quán của màu sắc. Note that when selecting the panel, it should be free of scars, warpage, trachoma, depressions, stains, etc. If the wool board does not show the effect, the panel can only be determined after spraying the board with a water gun. Lưu ý rằng khi chọn bảng điều khiển, không được có sẹo, cong vênh, đau mắt hột, trầm cảm, vết bẩn, v.v ... Nếu bảng len không hiển thị hiệu ứng, bảng chỉ có thể được xác định sau khi phun bảng bằng súng nước.
Người liên hệ: Mr. Arno Hao
Tel: +8618717894416